Pololu Zumo 75:1マイクロメタルギアモータHP [Pololu-2361]

Pololu Zumo 75:1マイクロメタルギアモータHP [Pololu-2361]

販売価格: 2,200円(税別)

(税込: 2,420円)

このギアモーターは (0.94インチ×0.39インチ×0.47インチ)の高品質、75.81:1メタルギアボックス付きの高出力のブラシDCモーターです(Sanyo製のポピュラーな12mmギアモーターに近いものです)。


これらは長さ0.365インチ、半径3mmのD型の出力シャフトが備え付けられています。

主なスペックは、

  • 6V:400RPM
  • 70mAでフリーラン
  • 22オンスインチ(1.6kg-cm)
  • 1.6Aでストール


■注意点
この商品は、シャフト部分がないためシャフト付ををご希望のお客様はこちらからお求めください。
75:1 Micro Metal Gearmotor HP with Extended Motor Shaft

 

Overview

These tiny brushed DC gearmotors are available in a wide range of gear ratios—from 5:1 up to 1000:1—and with five different motors: high-power 6 V and 12 V motors with long-life carbon brushes (HPCB), and high-power (HP), medium power (MP), and low power (LP) 6 V motors with shorter-life precious metal brushes. The 6 V and 12 V HPCB motors offer the same performance at their respective nominal voltages, just with the 12 V motor drawing half the current of the 6 V motor. The 6 V HPCB and 6 V HP motors are identical except for their brushes, which only affect the lifetime of the motor.

The HPCB versions (shown on the left in the picture below) can be differentiated from versions with precious metal brushes (shown on the right) by their copper-colored terminals. Note that the HPCB terminals are 0.5 mm wider than those on the other micro metal gearmotor versions (2 mm vs. 1.5 mm), and they are about 1 mm closer together (6 mm vs. 7 mm).

 

 

Versions of these gearmotors are also available with an additional 1 mm-diameter output shaft that protrudes from the rear of the motor. This 4.5 mm-long rear shaft rotates at the same speed as the input to the gearbox and offers a way to add an encoder, such as our magnetic encoder for micro metal gearmotors (see the picture on the right), to provide motor speed or position feedback.

With the exception of the 1000:1 gear ratio versions, all of the micro metal gearmotors have the same physical dimensions, so one version can be easily swapped for another if your design requirements change. Please see the micro metal gearmotor comparison table for detailed specifications of all our micro metal gearmotors. This dynamically-sortable table can help you find the gearmotor that offers the best blend of speed, torque, and current-draw for your particular application. A more basic comparison table is available below.

Rated
Voltage
Motor TypeStall
Current
@ Rated Voltage
No-Load
Speed
@ Rated Voltage
Approximate
Stall Torque
@ Rated Voltage


Single-Shaft
(Gearbox Only)


Dual-Shaft
(Gearbox & Motor)
 
 
12 Vhigh-power,
carbon brushes
(HPCB)
800 mA6000 RPM2 oz-in5:1 HPCB 12V5:1 HPCB 12V dual-shaft
3000 RPM4 oz-in10:1 HPCB 12V10:1 HPCB 12V dual-shaft
1000 RPM9 oz-in30:1 HPCB 12V30:1 HPCB 12V dual-shaft
625 RPM15 oz-in50:1 HPCB 12V50:1 HPCB 12V dual-shaft
400 RPM22 oz-in75:1 HPCB 12V75:1 HPCB 12V dual-shaft
320 RPM30 oz-in100:1 HPCB 12V100:1 HPCB 12V dual-shaft
200 RPM40 oz-in150:1 HPCB 12V150:1 HPCB 12V dual-shaft
140 RPM50 oz-in210:1 HPCB 12V210:1 HPCB 12V dual-shaft
120 RPM60 oz-in250:1 HPCB 12V250:1 HPCB 12V dual-shaft
100 RPM70 oz-in298:1 HPCB 12V298:1 HPCB 12V dual-shaft
32 RPM125 oz-in1000:1 HPCB 12V1000:1 HPCB 12V dual-shaft
 
 
6 Vhigh-power,
carbon brushes
(HPCB)
1600 mA6000 RPM2 oz-in5:1 HPCB 6V5:1 HPCB 6V dual-shaft
3000 RPM4 oz-in10:1 HPCB 6V10:1 HPCB 6V dual-shaft
1000 RPM9 oz-in30:1 HPCB 6V30:1 HPCB 6V dual-shaft
625 RPM15 oz-in50:1 HPCB 6V50:1 HPCB 6V dual-shaft
400 RPM22 oz-in75:1 HPCB 6V75:1 HPCB 6V dual-shaft
320 RPM30 oz-in100:1 HPCB 6V100:1 HPCB 6V dual-shaft
200 RPM40 oz-in150:1 HPCB 6V150:1 HPCB 6V dual-shaft
140 RPM50 oz-in210:1 HPCB 6V210:1 HPCB 6V dual-shaft
120 RPM60 oz-in250:1 HPCB 6V250:1 HPCB 6V dual-shaft
100 RPM70 oz-in298:1 HPCB 6V298:1 HPCB 6V dual-shaft
32 RPM125 oz-in1000:1 HPCB 6V1000:1 HPCB 6V dual-shaft
 
 
6 Vhigh-power
(HP)


(same specs as
6V HPCB above)
1600 mA6000 RPM2 oz-in5:1 HP 6V5:1 HP 6V dual-shaft
3000 RPM4 oz-in10:1 HP 6V10:1 HP 6V dual-shaft
1000 RPM9 oz-in30:1 HP 6V30:1 HP 6V dual-shaft
625 RPM15 oz-in50:1 HP 6V50:1 HP 6V dual-shaft
400 RPM22 oz-in75:1 HP 6V75:1 HP 6V dual-shaft
320 RPM30 oz-in100:1 HP 6V100:1 HP 6V dual-shaft
200 RPM40 oz-in150:1 HP 6V150:1 HP 6V dual-shaft
140 RPM50 oz-in210:1 HP 6V210:1 HP 6V dual-shaft
120 RPM60 oz-in250:1 HP 6V250:1 HP 6V dual-shaft
100 RPM70 oz-in298:1 HP 6V298:1 HP 6V dual-shaft
32 RPM125 oz-in1000:1 HP 6V1000:1 HP 6V dual-shaft
 
 
6 Vmedium-power
(MP)
700 mA4400 RPM1.5 oz-in 5:1 MP 6V dual-shaft
2200 RPM3 oz-in10:1 MP 6V10:1 MP 6V dual-shaft
730 RPM8 oz-in30:1 MP 6V30:1 MP 6V dual-shaft
420 RPM12 oz-in50:1 MP 6V50:1 MP 6V dual-shaft
290 RPM17 oz-in75:1 MP 6V75:1 MP 6V dual-shaft
220 RPM21 oz-in100:1 MP 6V100:1 MP 6V dual-shaft
150 RPM28 oz-in150:1 MP 6V150:1 MP 6V dual-shaft
100 RPM36 oz-in 210:1 MP 6V dual-shaft
90 RPM41 oz-in 250:1 MP 6V dual-shaft
75 RPM46 oz-in298:1 MP 6V298:1 MP 6V dual-shaft
22 RPM80 oz-in1000:1 MP 6V1000:1 MP 6V dual-shaft
 
 
6 Vlow-power
(LP)
360 mA2500 RPM1 oz-in5:1 LP 6V5:1 LP 6V dual-shaft
1300 RPM2 oz-in10:1 LP 6V10:1 LP 6V dual-shaft
440 RPM4 oz-in30:1 LP 6V30:1 LP 6V dual-shaft
250 RPM7 oz-in50:1 LP 6V50:1 LP 6V dual-shaft
170 RPM9 oz-in75:1 LP 6V75:1 LP 6V dual-shaft
120 RPM12 oz-in100:1 LP 6V100:1 LP 6V dual-shaft
85 RPM17 oz-in150:1 LP 6V150:1 LP 6V dual-shaft
60 RPM27 oz-in210:1 LP 6V210:1 LP 6V dual-shaft
50 RPM32 oz-in250:1 LP 6V250:1 LP 6V dual-shaft
45 RPM40 oz-in298:1 LP 6V298:1 LP 6V dual-shaft
14 RPM70 oz-in1000:1 LP 6V1000:1 LP 6V dual-shaft

Note: Stalling or overloading gearmotors can greatly decrease their lifetimes and even result in immediate damage. The recommended upper limit for instantaneous torque is 35 oz-in (2.5 kg-cm) for the 1000:1 gearboxes and 25 oz-in (2 kg*cm) for all the other gear ratios; we strongly advise keeping applied loads well under this limit. Stalls can also result in rapid (potentially on the order of seconds) thermal damage to the motor windings and brushes, especially for the versions that use high-power (HP and HPCB) motors; a general recommendation for brushed DC motor operation is 25% or less of the stall current.

In general, these kinds of motors can run at voltages above and below their nominal voltages; lower voltages might not be practical, and higher voltages could start negatively affecting the life of the motor.

Details for item #2361

Exact gear ratio: 34×34×35×3813×12×13×1075.81:134×34×35×3813×12×13×10≈75.81:1

Gearmotor Dimensions

In terms of size, these gearmotors are very similar to Sanyo’s popular 12 mm NA4S DC gearmotors, and gearmotors with this form factor are occasionally referred to as N20 motors. The versions with carbon brushes (HPCB) have slightly different terminal and end-cap dimensions than the versions with precious metal brushes, but all of the other dimensions are identical.

Dimensions of versions with carbon brushes (HPCB)

 

Dimensions of the Pololu micro metal gearmotors with carbon brushes (HPCB). Units are mm over [inches].

 

Dimensions of versions with precious metal brushes (LP, MP, and HP)

 

Dimensions of the Pololu micro metal gearmotors with precious metal brushes: low-power (LP), medium-power (MP), and high-power (HP). Units are mm over [inches].

 

These diagrams are also available as a downloadable PDF (262k pdf).

Motor Accessories

Pololu wheel 32×7mm on a micro metal gearmotor.

Black Pololu 70×8mm wheel on a Pololu micro metal gearmotor.

A pair of Pololu universal aluminum mounting hubs for 3 mm diameter shafts.

 

12mm Hex Wheel Adapter for 3mm Shaft on a Micro Metal Gearmotor.